S84-ex print engine replacement parts

Genuine SATO pressure roller assembly for S84NX and S84-ex, ensuring perfect print quality and fit for RH/LH models.

This is the direct replacement for the discontinued parts #R27602000 and #R27603000.

CN14 to DB25 connector to be used wiith Test Jig and S84ex/S86ex printer model.

A diagnostic interface tool designed for testing and troubleshooting SATO print engines. This test JIG allows technicians to verify I/O signals, check communication status, and perform functional diagnostics during setup, repair, or maintenance. Includes CN14 Adapter Cable 3 for direct connection to compatible print engines.

Note: To complete the setup, part number Y98130200002 (DB25 Adapter Cable for Test JIG – cable only) must be purchased separately.

This adapter cable converts previous M84xxSe and S84xx EXT port connector to current S84ex/S86ex connector.

2 gigabyte SD card for cloning settings between printers.

Antenna extension to boost WiFi signal on S84/S86NX, S84-ex/S86-ex and Lt408 printers.

Bluetooth upgrade kit that allows for Bluetooth interface communication. Kit requires installation on printer. Compatible with SATO S84ex/S86ex model printers.

Wi-Fi upgrade kit that allows for Wireless Local Area Network (WLAN) connections. Kit requires installation on printer. Compatible with SATO S84ex/S86ex model printers.

Kit which ads ability for ultra high frequency RFID printing on S84-ex left hand printers.

Kit which ads ability for ultra high frequency RFID printing on S84-ex standard right hand printers.

9 pin RS232 to 25 pin RS232 adapter cable. Compatible with SATO CLNX Plus, S84/S86NX and S84-ex/S86-ex model printers.

Left Hand (Opposite) Full Gear Box Assembly. Includes motor, belts, gears and bracket. All fully assembled. Only requires 3 screws to install.

Right Hand (Standard) Full Gear Box Assembly. Includes motor, belts, gears and bracket. All fully assembled. Only requires 3 screws to install.

Gear box belt for ribbon saver option (non-standard).

1 of 3 standard gear box belts. 274 mm in length.

1 of 3 standard gear box belts. 192 mm in length.

1 of 3 standard gear box belts. 340 mm in length.

Genuine SATO roller that rewinds the ribbon on thermal transfer printers.

Genuine SATO roller that feeds the ribbon on thermal transfer printers.

Genuine SATO part that functions as upper sensor for detecting I-Mark or gap in label stock.

Genuine SATO lower sensor that detects the I-Mark or gap in label stock.

Felt square that covers exhaust on rear of printer.

Genuine SATO electronic circuit board that controls LCD display.

Genuine SATO electronic circuit board that controls the motor feeding the label stock.

Genuine SATO electronic circuit board that provides necessary voltages to operate printer.

Genuine SATO electronic circuit board that controls printer and stores printer settings.

Genuine SATO print head that produces heat required to print. Compatible with SATO S84-ex model printers. 609 dot per inch print quality.

Genuine SATO print head that produces heat required to print. Compatible with SATO S84-ex model printers. 305 dot per inch print quality.

Genuine SATO print head that produces heat required to print. Compatible with SATO S84-ex model printers. 203 dot per inch print quality.

Genuine SATO platen roller for S84-ex print engines. Platen roller positions under label stock and print head to ensure print quality.

Genuine SATO feed roller, specifically crafted for the S84NX and S84-ex print engines, delivers precision and reliability in paper feeding. It is designed to seamlessly integrate with both RH and LH models.

Genuine SATO pressure roller, engineered exclusively for the S84NX and S84-ex print engines, guarantees precise and uniform pressure application across the media throughout the printing operation. This roller is fully compatible with both Right Hand (RH) and Left Hand (LH) models.